基于SWT方法的钢绞线索微动疲劳特性分析

为得到钢绞线索丝间接触区的应力场分布并预测微动疲劳裂纹萌生位置和微动疲劳寿命，本文利用参数化方法建立了精细化的钢绞线拉索有限元模型，包括整索模型和不同层丝间接触区域的局部精细化子模型．分析了钢绞线索在两种交变荷载工况下的应力场变化情况，并基于多轴疲劳SWT(Smith-Watson-Topper)临界平面法进行了疲劳特性分析和疲劳寿命预测．主要结论如下：钢绞线索内接触区边缘处的微动幅值较大，中心处几乎没有相对滑动，微动疲劳的初始裂纹萌生点位于接触区域边缘；经不同区域子模型分析比较，在轴向循环荷载作用下，外层钢丝的接触区域比内层钢丝更易发生微动疲劳损伤；在横向位移循环荷载作用下，同层钢丝因位置角度不同而产生了较大的疲劳特性差异，且相比轴向循环拉伸，该工况下最不利单丝的微动疲劳寿命更低；与非接触区域相比，接触区的疲劳寿命大幅降低，微动现象对钢绞线索的抗疲劳性能有明显降低作用．     

蓝宝石冲击消光晶向效应的第一性原理

蓝宝石的冲击消光现象是高压领域中的研究热点.低压段(86 GPa范围内)的实验研究表明蓝宝石的冲击消光与晶向相关,但在高压段(压力范围:131255 GPa)是否也具有晶向相关性目前尚不清楚.为此,利用第一性原理方法,分别计算了八个不同晶向的蓝宝石理想晶体和含氧离子空位缺陷晶体在高压段的光吸收性质,结果发现:1)蓝宝石在高压段的冲击消光表现出明显的晶向效应,且该效应还随压力增大而增强;一步的数据分析可以看出,在冲击实验采用的波段内,a晶向的消光最弱(透明性最好),c晶向的消光最强与c晶向的消光接近,g晶向的消光要弱于s晶向的消光.鉴于此,如果在高压段开展加窗冲击波实验,建议选择a晶向或m晶向的蓝宝石作为其光学窗口.本文结果不仅有助于深入地认识蓝宝石在极端条件下的光学性质,而且对未来的实验研究有重要的参考作用.     

分数阶Schrodinger—Kirchhoff方程无穷多高能量解的存在性

本文研究如下带有变号势函数的分数阶Schrodinger Kirchhoff方程(a+b∫∫R^N|u(x)-u(y)|^p/|x-y|^N+p^sdxdy)^p-1(-△)p^su+λV(x)|u|^p-2u=f(x,u)-μg(x)|u|^q-2u,x∈R^N.其中s∈(0,1),p∈[2,∞),q∈(l,p),a,b>0,λ,μ>0均为正常数,在V,f,g等函数合适的条件下,运用喷泉定理获得该系统无穷多高能量解的存在性.     

Meshless acoustic analysis using a weakly singular Burton-Miller boundary integral formulation

The Burton-Miller boundary integral formulation is solved by a complex variable boundary element-free method (CVBEFM) for the boundary-only meshless analysis of acoustic problems with arbitrary wavenumbers. To regularize both strongly singular and hypersingular integrals and to avoid the computation of the solid angle and its normal derivative, a weakly singular Burton-Miller formulation is derived by considering the normal derivative of the solid angle and adopting the singularity subtraction procedures. To facilitate the implementation of the CVBEFM and the approximation of gradients of the boundary variables, a stabilized complex variable moving least-square approximation is selected in the meshless discretization procedure. The results show the accuracy and efficiency of the present CVBEFM and reveal that the method can produce satisfactory results for all wavenumbers, even for extremely large wavenumbers such as k = 10 000.     

ICP-AES法测定高温合金中5种非金属元素

本文研究了快速测定高温合金中5种非金属元素(As、B、P、Se、Si)的分析方法,以满足高温合金行业对非金属元素检测的需求。利用王水和高氯酸对高温合金进行酸溶解,并系统研究了基体元素和共存元素对分析元素谱线的光谱干扰情况,同时进行了分析谱线的选择。5种非金属元素的检出限在5.5 ～ 11.9 ug/ml,5次数据的相对标准偏差(RSD,n=5)为0.9 % ～ 7 %,各元素的回收率在96 % ～ 102 %之间,该方法适用于高温合金中非金属元素的测定。     

Effect of branched alkyl side chains on the performance of thin‐film transistors and photovoltaic cells fabricated with isoindigo‐based conjugated polymers

New isoindigo and di(thienyl)ethylene‐containing π‐extended conjugated polymers with different branched side chains were synthesized to investigate their physical properties and device performance in thin‐film transistors and photovoltaic cells. 11‐Butyltricosane (S3) and 11‐heptyltricosane (S6) groups were used as side‐chain moieties tethered to isoindigo units. The linking groups between the polymer backbone and bifurcation point in the branched side chain differ in the two polymers (i.e., PIDTE‐S3 and PIDTE‐S6 ). The polymers bearing S6 side chains showed much better charge transport behavior than those with S3 side chains. Thermally annealed PIDTE‐S6 film exhibited an outstanding hole mobility of 4.07 cm² V^?1 s^?1 under ambient conditions. Furthermore, bulk heterojunction organic photovoltaic cells made from a blend film of PIDTE‐S3 and (6,6)‐phenyl C61‐butyric acid methyl ester demonstrated promising device performance with a power conversion efficiency in the range of 4.9–5.0%. © 2015 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 2015 , 53, 1226–1234     

A general analytical method for evaluation of the thermodynamic properties of matters using virial coefficients with Morse potential at high temperature

In this paper, we established an analytical formula for the second virial coefficient (SVC) with Morse potential without using any numerical methods, and the obtained formula is applied to the calculation of the speed of sound of some matter at high temperature. This approach is based on the series expansion formula and special functions, which allows the exact evaluations of any thermodynamic properties of matter using the SVC. As an application, the obtained analytical formula is used for evaluation of the SVC with Morse potential for high‐temperature gas and the plasma region of the intermolecular interactions of neutral atom gases of B, Si, Zn, H₂, N₂, O₂, NO, CO, He, Ne, Ar, Kr , and Xe . Based on the obtained formula of SVC, the speed of sound for gases of N₂, Ar , and Zn are also determined analytically. A specific maximum temperature is chosen for every gas to ensure that there are still neutral atoms in the gas, and low temperatures are avoided due to quantum effects. The results are compared with numerical data and another analytical data from the literature. The new analytical solution is shown to be in good agreement with the compared data and is verified to supply proper thermodynamic data.     

Elongation improvement in nano bainite steel obtained from plastically deformed primary austenite

ABSTRACT

Ausforming is being widely used to overcome the kinetics barrier in nanostructured bainitic steels and to enhance its practical industrial applications. It would also affect the microstructural characteristics and consequently the resultant mechanical performance. This article aims to investigate the tensile behaviour of nano bainite obtained from plastically deformed primary austenite at three different heat treatment stages. 10% of ausforming has been implemented and nanostructured bainite obtained after austempering at 300°C for 2, 4 and 6?h in salt bath furnaces. Results indicated that ausforming could successfully increase the volume fraction of bainite within the microstructure and refine the bainite packets sizes. Moreover, it has been demonstrated that higher mechanical stability of retained austenite and therefore more effective TRIP effect could be attained during the tensile test which consequently resulted in elongation improvement without deteriorating the strength properties. This claimed to be beneficial for materials performance during practical applications.     

Assessment of a high‐order MUSCL method for rotor flows

This work presents the implementation of a high‐order, finite‐volume scheme suitable for rotor flows. The formulation is based on the variable extrapolation MUSCL‐scheme, where high‐order spatial accuracy (up to fourth‐order) is achieved using correction terms obtained through successive differentiation. A variety of results are presented, including 2‐ and 3‐dimensional test cases. Results with the proposed scheme, showed better wake and higher resolution of vortical structures compared with the standard MUSCL, even when coarse meshes were employed. The method was also demonstrated for 3‐dimensional unsteady flows using overset and moving grids for the UH‐60A rotor in forward flight and the Enhanced Rotorcraft Innovative Concept Achievement tiltrotor in aeroplane mode. For medium grids, the present method adds reasonable CPU and memory overheads and offers good accuracy on relatively coarse grids.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.